Jump to content
Create New...

Project Achieva


Recommended Posts

Its been nearly 5000 Kilometers since the repair (yeah, fun June!).

She gets 23/24MPG city like clockwork, and Iv got her to 28.5MPG mixed!

But....

Theres a new problem brewing.

As of last week, it looks like transmission fluid is dripping out!!! :mind-blowing: .

:banghead:

IMG_0592.jpg

IMG_0616.jpg

IMG_0532.jpg

Link to comment
Share on other sites

Is it leaking from the pan or the bellhousing?

Im not sure. She is due for an oil change, so when its on the lift will be the best time to investigate.

Im gonna take some pics today underneath.

Im not %100 sure if it is trans fluid, but its pinkish so seems most likely.

LOL

Ongoing saga!

Link to comment
Share on other sites

  • 3 weeks later...

While on vacation in Stayner Ontario, I visited a scrap yard, and got myself some nicer radio knobs, buttons and cigarette lighter from a 1990 Chevrolet Cavalier sedan.

31529630050_large.jpg31529630051_large.jpg

31529630052_large.jpg31529630053_large.jpg

31529630054_large.jpg31529630055_large.jpg

31529630056_large.jpg31529630057_large.jpg

Before and after:

31529630058_large.jpg31529630059_large.jpg

31529630060_large.jpg

31529630061_large.jpg

31529630062_large.jpg

A little classier, nicer tactile feel, and better visibility at night!

Link to comment
Share on other sites

I am not even going to mention anything about polished knobs in this post. But yeah, they do make a difference. Did you know you can get billet aluminum HVAC knobs that will likely fit your control unit?
Link to comment
Share on other sites

I am not even going to mention anything about polished knobs in this post. But yeah, they do make a difference. Did you know you can get billet aluminum HVAC knobs that will likely fit your control unit?

:scratchchin:

Ima hit some local scrap yards this week and see what else I can scrounge up.

I want to get some kick plates, and spray paint them silver (saving my originals). :scratchchin:

In preparation for this, the other day I replaced all the screws holding the kick plates down. Most were completely rusted and badly degraded.

Would you happen to know the correct size of screw (cause I kinda winged it and got simular screws at WalMart). I would like to replace the screws holding down the plastic panel around the inside (where the door meets the car). They are skinnier and longer (yeah, whata setup!).

Im not that handy, but Im learning.

Update about that leak: it seems to have stopped mysteriously. New cardboard last 2 days, and its dry. WTF? :confused0071:

Link to comment
Share on other sites

????

gmc-acadia-035-center.jpg

Maybe it was' the Acadia, I or maybe it was just the stereo knob. I can't remember. Basically you hollow out one of GM;s chrome ring knobs, then sand down the LH knobs and fit them in, securing them with epoxy. It was a really cool mod. I have to look for it again.

Link to comment
Share on other sites

  • 2 weeks later...

Project Achieva update:

The leak, whatever it was, has stopped. I had an oil channge done, and the bottom of the transmission is clean, no signs of leakage.

All the oil was accounted for also. :scratchchin:

I was up in Stayner Ontario again, and went back to the scrap yard for some more pickins'.

It seems that I forgot the "front/rear/right/left" knobs (that go under the main radio knobs) the first time around. Luckily, the poor Cavalier was still there, so I got them.

Also got the kick plates and rear ashtray from a 1996 Buick Skylark.

The ashtray replaces the black one I have now (already installed, and looks great), while the kickplates will be painted chrome :AH-HA_wink: (to be done tonight).

I also got the HVAC knobs, but they don't really work in the pre-96 dash. May play with them in the 95 Lumina.

The Oldsmobile script is from a G-body Cutlass coupe front bumper.

The Olds rocket emblems are from the rear clip of a late 70's full size Olds (forgot what exactly). They are now installed on my front inside door panels (ala 60's Oldsmobiles). It also had some amazing interior trim, but was infested with bees! I woulda braved it, but I decided it was too nice to pilage (and risk getting stung).

The RAM badge will make a nice keychain for a friend with a '97 Ram short cab/long bed :smilewide: .

Pre-clean-up pic:

IMG_3103.jpg

I mainly want to add some brightwork to the Achieva interior. Something Oldsmobiles in the past always had.

The buttons/lighter and ashtray make a big difference, and I hope the kickplates come out looking ok.

Being a purist, I am keeping all the stock bits. Everything I am doing can be reversed.

Link to comment
Share on other sites

I know what you mean about wanting to add brightwork. Adding the chrome handles, switches, gauges and shifter really brighten up the cabin in my car.

What are you using to paint the kickplates? Last time I used chrome paint it was nothing more than silver, and wasn't durable at all.

Link to comment
Share on other sites

What are you using to paint the kickplates? Last time I used chrome paint it was nothing more than silver, and wasn't durable at all.

I don't have it infront of me, but its a tall can of spray paint, that is appearantly chrome colored.

It was $9 at WalMart.

If it doesn't work, I can always get more kickplates and experiment. :smilewide:

I wonder if I could use it to paint the engine cover?

Link to comment
Share on other sites

I don't have it infront of me, but its a tall can of spray paint, that is appearantly chrome colored.

It was $9 at WalMart.

If it doesn't work, I can always get more kickplates and experiment. :smilewide:

I wonder if I could use it to paint the engine cover?

You need to use high-heat primer, paint, and clear coat for that. I got away with using regular silver for the lettering, but it's just a small portion and I covered the whole thing with 3 coats of high heat clear.

Link to comment
Share on other sites

You need to use high-heat primer, paint, and clear coat for that. I got away with using regular silver for the lettering, but it's just a small portion and I covered the whole thing with 3 coats of high heat clear.

Yeah, I figured as much. Its actually very clean. I bet i could just polish it up actually. :scratchchin:

Link to comment
Share on other sites

The radio is now more inline with the Achievas fancier predecessor, the Calais:

2218016503_98024ddaf5_o.jpg

Complete radio knobs...classy:

IMG_3283.jpg

IMG_3287.jpg

Door emblems:

IMG_3290.jpg

IMG_3293.jpg

New rear ashtray:

IMG_3308.jpg

Spray painting the kickplates (it went pretty well, and looks alright. Shiny!):

IMG_3326.jpg

IMG_3327-1.jpg

IMG_3331.jpg

IMG_3333.jpg

IMG_3347.jpg

IMG_3357.jpg

IMG_3359.jpg

Now, gotta wait for it to dry and see how it looks on the car!

Link to comment
Share on other sites

It doesnt really translate in pictures, but they look very shiny in person. At night, they are very visible under the courtesy lights. I didn't clear coat them. Im thinking of giving them a second coat of "chrome". First time Iv done something like this, so I dunno?

Link to comment
Share on other sites

  • 1 month later...

Project Achieva Updates:

The "chrome" kickplates are holding up OK. The drivers side (ie most used) did scratch a little. I didn't do a second coat, and no clear coat.

August 20, 2009:

1997 Pontiac Grand Am GT sun visors installed. My old ones had sagging straps. New visors have extendable sunshades too!

before:

IMG_3989.jpg

after:

IMG_4015.jpg

old (top), new (bottom):

IMG_4006.jpg

August 21, 2009:

Blue 1969 Ontario licence plates. Look cool at car shows!

IMG_4036.jpg

IMG_4044.jpg

August 23, 2009:

The Achievas car show debut! 1st annual North York Chevrolet All GM show.

IMG_4227.jpg

September 29, 2009:

188,888.8 KM!

IMG_6488.jpg

October 7, 2009:

RIMZ!!!!!! 2000 Cavalier Z24 16"ers! Will get cleaned up and put on the car within the next 2 weeks!

IMG_6522.jpg

IMG_6538.jpg

its gonna look awesome!

IMG_6536.jpg

October 8, 2009:

#1 Achieva on CarDomain!

a2.jpg

And the latest is that the AC compressor is crapping out.

Much more adventures ahead!

PS, heres something for dodgefan...

IMG_6453.jpg

Link to comment
Share on other sites

Hope you get Olds center caps for those Cav wheels.

Thats gonna be a problem, as they are 2" centers, and as far as I know, there are no OEM Olds caps that size.

Plan B is custom stickers. Don't worry, Im all about the details! :cutlass:

First order of business is to sort out the AC compressor noise/any other possible issue. :explode:

I hope the end results are as follows:

9030_136716764169_518014169_2393074_4712

*photochop

Link to comment
Share on other sites

  • 2 years later...

Time for a big update...since its been...2 years!?!

Where did we leave off...um...late '09 right?

The Achieva had a rocking 2010 season, travelling to many many car shows!

The Z24 wheels where installed in March...

24074_376127814169_518014169_3495404_8089086_n.jpg

31706_395363349169_518014169_3908015_6211294_n.jpg

It turned a lot of heads!

31706_393920369169_518014169_3881338_6599180_n.jpg

39728_421999014169_518014169_4590470_779936_n.jpg

In August, the heater core blew up! I had it by-passed.

45056_427886824169_518014169_4736181_1343608_n.jpg

Around September, the transmission failed completely....and the project was once again shelved.

I had an estimate of $1600 to install a new tranny!

After debating for months, I bit the bullet and saved the car!!!

On December 11, the Achieva once again roared back to life...

68154_476551724169_518014169_5544544_139198_n.jpg

...And was promptly put to severe winter driving!!! (WITH NO HEAT...remember...by-passed heater core! d'oh!)

162950_477757609169_518014169_5565181_6736874_n.jpg

165763_480923584169_518014169_5602589_1295838_n.jpg

To be continued in 2011..................

Edited by !!!TED!!!
Link to comment
Share on other sites

Achieva in 2011:

The year started out hopefull.

I was attending classes for Automotive Engines....a course supplied by GM with 3100 V6's to dismantle (perfect!)

164722_489445934169_518014169_5724959_4882160_n.jpg

168631_494414869169_518014169_5795218_1649128_n.jpg

In February, she was put back on the stock wheels, as the tires for the Z24's had gotten really bad...

180069_10150100632269170_518014169_6063391_2031525_n.jpg

March 15 2011:

198129_10150121653504170_518014169_6266398_4650360_n.jpg

At the end of March, I bought another set of Z24 wheels in mint condition, with near new tires!

On the car they went...good to go for the car show season!

199761_10150130495509170_518014169_6343780_2815122_n.jpg

198980_10150132183709170_518014169_6363905_6969818_n.jpg

206552_10150132486349170_518014169_6366811_2344979_n.jpg

208687_10150132484784170_518014169_6366770_840908_n.jpg

March 31, 2011:

205338_10150147007409170_518014169_6382740_6962488_n.jpg

The Achieva ran flawless...and everything was peachy once again!

April 7, 2011:

217509_10150154039369170_518014169_6444291_5834119_n.jpg

April 17, 2011:

208294_10150161163574170_518014169_6510781_2738691_n.jpg

To be continued.....

Link to comment
Share on other sites

It was a beautiful, sunny spring day on May 7, 2011.

I had detailed the car, and went for a 100km drive on my favorite roads!

225226_10150177597619170_518014169_6666382_8107589_n.jpg

225710_10150177597669170_518014169_6666383_2432143_n.jpg

229309_10150177597864170_518014169_6666388_8300_n.jpg

229791_10150177597954170_518014169_6666391_423574_n.jpg

226959_10150177608914170_518014169_6666486_516076_n.jpg

I drove back to the city with a big smile on my face!

Before I got home, I decided to stop at the bank.

As tried to start the car again, it wouldn't crank!!!

After failing to boost it, and having it towed to a local shop..it was found that the starter had gone bad.

A new starter was installed...and she started....but to my horror.....puttered, and died again. Some piston rings had come loose on the #3 cylinder, causing the engine to fail!!!! &^$&*($&^$&^

What to do...what to do?!?!?

Project Achieva was ONCE AGAIN put on hold.

May 29, 2011:

254073_10150197687479170_518014169_6826294_317658_n.jpg

I had an estimate of $2200 to drop a new engine in!

It was very painful, but the decision was made to get another car.

Car searching commenced....

Link to comment
Share on other sites

And then I snapped out of it.

Wait a second....I want an F-body! I'm not an old granny..why am I looking at old granny cars!!!???

The search turned to SPORTS CARS of the Camaro/Firebird persuation!

Now, If you know me (from the boards or otherwise, you know I'v long been a huge Camaro fan).

As fate would have it....things turned out quite different...

I looked at a few Camaro's, and even

....had dibs on this glorious Trans Am:

254099_10150209988529170_518014169_6934666_284926_n.jpg

Link to comment
Share on other sites

After my Birthday on July 3, 2011, my uncle asked me if I wanted to see a car he found.

We traveled 1 hour outside of the city, and I was greeted with this gem:

264642_10150247925159170_518014169_7180807_8010514_n.jpg

A 1996 Pontiac Firebird. One family owned. 3800 V6 producing 200HP. 47,320 Kilometers. Cloth interior, automatic, power everything. Runs and drives like brand new, with working A/C!

After hagling on the price, and hammering out the paperwork, I drove her home July 6th!

268358_10150244354774170_518014169_7145691_205273_n.jpg

I had now become an F-body owner!!!!

269115_10150247924904170_518014169_7180805_1899484_n.jpg

269942_10150247925379170_518014169_7180809_108841_n.jpg

261464_10150247925524170_518014169_7180812_5576899_n.jpg262061_10150247925609170_518014169_7180814_1551202_n.jpg268778_10150247925719170_518014169_7180816_2734603_n.jpg

Not a crooked hood, but plastic black edge liner...which was later removed...268621_10150247925789170_518014169_7180818_968834_n.jpg

The dealer badge was also later removed by me....The tramp stamp...is still there :D

261825_10150247925924170_518014169_7180820_132444_n.jpg

Edited by !!!TED!!!
Link to comment
Share on other sites

My new car had its official debut at an All-GM Show on June 11, 2011:269801_10150247927959170_518014169_7180852_4377312_n.jpg

261728_10150247926029170_518014169_7180822_3899422_n.jpg

264120_10150247926159170_518014169_7180825_892627_n.jpg

My friends cars, back to front: Mike/black G8, Eric/red '99 Z28, Billy red '02 Z28, me :D

264210_10150247926259170_518014169_7180827_6088455_n.jpg

268359_10150247926419170_518014169_7180831_1238950_n.jpg

269789_10150247926569170_518014169_7180835_7076451_n.jpg261743_10150247926804170_518014169_7180838_6692584_n.jpg

268328_10150247927049170_518014169_7180840_2156226_n.jpg

262291_10150247924764170_518014169_7180803_3925335_n.jpg

To be continued....... :breakdance:

Edited by !!!TED!!!
Link to comment
Share on other sites

Welcome to the cult of the Poncho.

Shame to hear you gave up on the Achieva, after you took so much care of it. I feel you could have swapped in another engine for considerably less than $2200.

That said, the Firebird is more in the styling of your !!!TED!!! logo. Good luck with it.

Link to comment
Share on other sites

Nice Firebird. That was a pretty nice selection of low mileage cars you were able to choose from. A certain former C&Ger would be impressed with that 98.

I had a smile that you still had the tape on the hood of your Achieva. Too bad the paint was coming up with it.

Link to comment
Share on other sites

Welcome to the cult of the Poncho.

Shame to hear you gave up on the Achieva, after you took so much care of it. I feel you could have swapped in another engine for considerably less than $2200.

That said, the Firebird is more in the styling of your !!!TED!!! logo. Good luck with it.

I didn't give up! I wanted to fix her (once again), but everyone was against me (family: STOP THE MADNESS TED, friends: let her die a graceful death)!!! I found a mechanic who was going to install a complete low milage engine and tranny for $1800 all in. It was to happen the week I found the Firebird!

Nice Firebird. That was a pretty nice selection of low mileage cars you were able to choose from. A certain former C&Ger would be impressed with that 98.

I had a smile that you still had the tape on the hood of your Achieva. Too bad the paint was coming up with it.

The stripes stayed BECAUSE of the peeling issue. I never attempted to remove them! Mr. 98 would have been proud indeed lol!

Link to comment
Share on other sites

The saga continues.....

So now, I had a new car.

The poor Achieva sat dead for a while. Having spent $1600 on a new transmission, and more recently $300 on perfect wheels and near new tires....I needed to recoup the money. More importantly to me, I wanted the car to go to someone who could keep it going, and not scrap her!

August 10, 2011:

283383_10150275153229170_518014169_7439901_7304601_n.jpg

A few people came by, but mainly tire kickers, and scrappers.

Then, I got a serious buyer, but he was only willing to give me $250. I really needed my parking spot back at this point, so I said screw it.....lets get it over with...

Before the buyer came, I took the wheels off the car, and put the stocks back on....

August 29, 2011:

310010_10150291688849170_518014169_7599379_2179577_n.jpg

321551_10150291689619170_518014169_7599390_5157375_n.jpg

310167_10150291690744170_518014169_7599401_2399288_n.jpg

I also discovered considerable frame damage due to excessive rust!

301699_10150291692304170_518014169_7599426_110534_n.jpg

301848_10150291692564170_518014169_7599434_6085906_n.jpg

The car was sold that afternoon.

Here is the final video of her leaving my garage.

After I shut the camera off...I cried (man tears..come on...you would too!)

Edited by !!!TED!!!
Link to comment
Share on other sites

But wait!!!!

There's more!!

A buyer by the name of Joe contacted me about the wheels/tires. He claimed to be my biggest fan! :huh:

Apparently, he had been following my "project" on YouTube, and was the owner of a 1998 blue Achieva! He wanted to make his look like mine (stripes and all!).

When he came down, he showed me his cell phone, which had my car as the backround! :blink:

He let me take a spin in his car around the block lol!!!

He was happy to pay $300 for the wheels, and revealed he is friends with my Camaro/Firebird clubs president! (WOW small world!)

We where having a big fall show soon, and he said he would come by with the wheels on his car to show me!

Aaaaand......so he did.......

311006_10150323136304170_1852233331_n.jpg

So...a little piece of my car lives on....and the spirit lives on!

Joe says he will have black stripes (professionaly done vinyl!) on the hood for this car show season!

I can't wait to see it! :breakdance:

I told him that I wish he had come by earlier. I would have given him my car as a parts car! That was the kind of person I was looking for!

Edited by !!!TED!!!
Link to comment
Share on other sites

So ends Project Achieva, June 2, 2008 - August 29, 2011.

Some might say I wasted a lot of money on a lowly clunker.

To me, she was worth every penny. A rare, cool GM car, that is becoming very scarce nowadays.

From dirty, unloved day one:

205686_14691379169_518014169_479955_2280_n.jpg

To rocket action....

229791_10150177597954170_518014169_6666391_423574_n.jpg

You never forget your first car!

Edited by !!!TED!!!
Link to comment
Share on other sites

I figured something was up with the silver Firebird in your signature, and no Achieva in sight. I also wanted to wait for you to post the story on your own, and what a great story it was (though sad in some ways). As a former owner of a '95 Pontiac Trans Am with T-tops, I sure do admire your new car. I gotta say though - grandma-ish or not, that '92 Ninety-Eight would have been a nice car to own too (and our friend, 98 Rgency, would have definitely approved of that purchase).

I'm glad you found your way back to C&G... a lot of the old timers are gone or don't publicly show themselves. I know you'll treat your Firebird very well, seeing as how you took care of the Achieva all of these years. What are your plans, if any, for the Poncho?

Link to comment
Share on other sites

I'm glad you found your way back to C&G...

Same here, Ted. VERY good to see these new posts from you. When I saw this topic pop up in the "unread" files, I thought, wait, what? :)

Cort | 38.m.IL | pigValve + paceMaker + cowValve | 5 MCs + 1 Caprice Classic

CHD.MCs.CC + RoadTrips.hobbies.RadioShows.us66 = http://www.chevyasylum.com/cort

* rNw-CC+event: http://rdwhl-capriceclassic.proboards.com/index.cgi?board=whatsgoingon *

"This can't be the end" __ Bertie Higgins __ 'Key Largo'

Link to comment
Share on other sites

  • 2 months later...

Hey there, Ted. Just read the whole thread, couldn't wait to drop some suggestions, but since you replaced it with the Firebird, they all still apply:

-That Achieva could've used a 3800 swap and a turbo (you should see the YouTubes of the W-bodies and swaps into other platforms). But the turbo still applies to this and all 3800 cars (including 98s and Cieras)!

-Definitely could stand to be stanced FTW!

-And for the love of Jeezus, stop driving your pride and joy in that awful Ontario salt! Let the frame of the Achieva be a lesson to you.

Link to comment
Share on other sites

Join the conversation

You are posting as a guest. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



×
×
  • Create New...

Hey there, we noticed you're using an ad-blocker. We're a small site that is supported by ads or subscriptions. We rely on these to pay for server costs and vehicle reviews.  Please consider whitelisting us in your ad-blocker, or if you really like what you see, you can pick up one of our subscriptions for just $1.75 a month or $15 a year. It may not seem like a lot, but it goes a long way to help support real, honest content, that isn't generated by an AI bot.

See you out there.

Drew
Editor-in-Chief

Write what you are looking for and press enter or click the search icon to begin your search